Индикаторы Ups 5000

Uninterruptible Power Supply

Tower/Rack-Mount 5U
VA
/ Vac
English

A 04/
Start-up

Start-up
Connect Equipment and Power to the UPS
1. The UPS features a chassis ground connection screw located on the rear panel, for connecting the ground
leads on transient voltage devices.
Prior to connecting the grounding wire, ensure that the UPS is NOT connected to utility or battery
power.
2. Connect equipment to the UPS.
3. V models: Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using
extension cords.
V models: Refer to the Input Hardwire section in this manual.
4. To use the UPS as a master on/off switch be sure all connected equipment is switched on.
Rear Panels
V models

V models

Start the UPS

10 Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual

Operation
Display Panels
V models

V models

Display Panel Indicators and Function Buttons

Indicator
Indicator Title Description
LED

AVR Trim The UPS is compensating for a high utility voltage. Refer to the APC Web site,
eunic-brussels.eu for AVR settings.
On Line The UPS is supplying utility power to the connected equipment,
(see Troubleshooting in this manual).
AVR Boost The UPS is compensating for a low utility voltage. Refer to the APC Web site,
eunic-brussels.eu for AVR settings.
Overload The connected equipment is drawing more than the UPS power rating allows,
(see Troubleshooting in this manual).
On Battery The UPS is supplying battery power to the connected equipment.

Disconnected Battery/ The battery is disconnected or must be replaced,

12 Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual

Indicator
Indicator Title Description
LED

V V
Diagnostic The UPS has a diagnostic feature that indicates the utility voltage.
Utility Voltage The UPS starts a self-test as part of this procedure. The self-test does not affect the
voltage display.

Press and hold the button to view the utility voltage bar graph indicator. As
Battery soon as the on-line LED starts flashing indicating a self-test is in progress, the
Charge five-LED Battery Charge indicator will show the utility input voltage.
Refer to the figure on the left for the voltage reading.
Values are not listed on the UPS.
The indicator on the UPS shows the voltage is between the displayed value on the
list and the next higher value, (see Troubleshooting in this manual).

Feature
Feature Title Function
Button

Power On Press this button to turn on the UPS. Continue reading for additional
capabilities.

Self-Test Automatic: The UPS performs a self-test automatically when turned on,
and every two weeks thereafter (by default). During the self-test, the UPS
briefly operates the connected equipment on battery.

Manual: Press and hold the button for a few seconds to initiate the
self-test.

Cold Start When there is no utility power and the UPS is off, the cold start feature will
switch the UPS and connected equipment onto battery power,
(see Troubleshooting in this manual).

Power Off Press this button to turn off the UPS.

Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual 13

Configuration
UPS settings
Settings are adjusted through PowerChute software or optional SmartSlot accessory cards.

Factory User Selectable

Automatic On startup and • On startup and every Set the interval at which the UPS will execute a
Self-Test every 14 days 7 days ( hours) self-test.
( hours) there after
there after • On startup and every
14 days ( hours)
there after
• On startup only
• No self-test

UPS ID UPS_IDEN Up to eight characters Uniquely identify the UPS, (i.e. server name or
(alphanumeric) location) for network management purposes.

Date of Last Manufacture mm/dd/yy Reset this date when you replace the battery
Battery Date module.
Replacement

Minimum Capacity 0 percent • 0% • 60% Specify the percentage to which batteries will
Before Return from • 15% • 75% be charged following a low battery shutdown
Shutdown • 30% • 90% before powering connected equipment.
• 45%

Voltage Sensitivity High sensitivity Brightly Adjust by pressing the VOLTAGE SENSITIVIY
The UPS detects illuminated: high switch (rear panel). Use a pointed object, (such
and reacts to line sensitivity as a pen) to do so.
voltage distortions Dimly illuminated: Note: In situations of poor power quality, the
by transferring to medium sensitivity UPS may frequently transfer to battery
battery operation to No illumination: operation. If the connected equipment can
protect the low sensitivity operate normally under such conditions, reduce
connected the sensitivity setting to conserve battery
equipment. capacity and service life.

Alarm Delay Enable • Enable Mute ongoing alarms or disable all alarms.
Control • Mute
• Disable

Shutdown Delay 90 seconds • 0s • s Set the interval between the time when the UPS
• 90 s • s receives a shutdown command and actual
• s • s shutdown.
• s • s

14 Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual

Factory User Selectable

Low Battery 2 minutes Brightly The low-battery warning beeps are continuous
Warning illuminated: when two minutes of run time remain.
PowerChute LED is located low battery warning To change the default interval setting, use a
software interface on rear panel level of about 2 minutes pointed object such as a pen to press the
provides automatic, Dimly illuminated: VOLTAGE SENSITIVIY switch (rear panel),
unattended while
shutdown when low battery
approximately two warning level of about
5 minutes pressing the button, (front display).
minutes of battery
operated run time No illumination: Change the low battery warning interval setting
remains. to the time that the operating system or system
low battery warning software requires to safely shut down.
level is about 8 minutes

Synchronized 0 seconds • 0s • s Specify the time the UPS will wait after the
Turn-on Delay • 60 s • s return of utility power before start up, (to avoid
• s • s branch circuit overload).
• s • s

High Transfer Point V models: To avoid unnecessary use of the battery where
Vac • Vac • Vac utility voltage is chronically high, set the high
• Vac transfer point higher if the connected
Vac
equipment can tolerate this condition.
V models:
Vac • Vac • Vac
• Vac • Vac

Low Transfer Point V models: • • To avoid unnecessary use of the battery where
Vac • Vac • Vac utility voltage is chronically low, set the low
• Vac • Vac transfer point lower if the connected equipment
can tolerate this condition.
V models:
Vac • Vac • Vac
• Vac • Vac

Output Voltage Set the output voltage of the UPS.

Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual 15

Troubleshooting
Use this chart to solve minor UPS installation and operation problems. Refer to eunic-brussels.eu for assistance
with complex UPS problems.

Problem and/or Possible Cause Solution

UPS will not turn on

The battery is not connected properly. Check that the battery connector is fully engaged.

button not pushed. Press the button once to power-up the UPS and connected equipment.

The UPS is not connected to utility Check that the power cable from the UPS to the utility power supply is
power supply. securely connected at both ends.

Very low or no utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the
light is very dim, have the utility voltage checked.

UPS will not turn off

The UPS is experiencing an internal Do not attempt to use the UPS. Unplug the UPS and have it serviced
fault immediately.

UPS beeps occasionally

Normal UPS operation when running None: The UPS is protecting the connected equipment. Press the button
on battery. to silence this alarm.

UPS is not providing expected backup time

The UPS battery(s) are weak due to a Charge the battery(s). Batteries require recharging after extended outages.
recent power outage or battery(s) are Batteries can wear faster when put into service often or when operated at
near the end of their service life. elevated temperatures. If the battery(s) are near the end of their service life,
consider replacing the battery(s) even if the replace battery LED is not yet
illuminated.

All LEDs are illuminated and the UPS emits a constant beeping

The UPS is experiencing an internal Do not attempt to use the UPS. Unplug the UPS and have it serviced
fault. immediately.

Front panel LEDs flash sequentially

The UPS has been shut down remotely None: The UPS will restart automatically when utility power returns.
through software or an optional
accessory card.

All LEDs are off and the UPS is plugged into a wall outlet

The UPS is shut down or the battery is None: The UPS will restart automatically when utility power is restored and
discharged from an extended outage. the battery has a sufficient charge.

16 Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual

Problem and/or Possible Cause Solution

The Overload LED is illuminated and the UPS emits a sustained alarm tone

The UPS is overloaded. The connected equipment exceeds the specified “maximum load” as defined
in Specifications on the APC Web site, eunic-brussels.eu
The alarm remains on until the overload is removed. Disconnect nonessential
equipment from the UPS to eliminate the overload condition.
The UPS continues to supply power as long as it is online and the circuit
breaker does not trip; the UPS will not provide power from batteries in the
event of a utility voltage interruption.

The Disconnected Battery/Replace Battery LED is illuminated

The Disconnected Battery/Replace Check that the battery connectors are fully engaged.
Battery LED flashes and a short beep is
emitted every two seconds to indicate
the battery is disconnected.

Weak battery Allow the battery to recharge for 24 hours and perform a self-test. If the
problem persists after recharging, replace the battery.

Failure of a battery self-test: Replace Allow the battery to recharge for 24 hours. Perform the self-test procedure to
Battery/Battery Disconnected LED confirm the replace battery condition. The alarm stops and the LED clears if
illuminates and the UPS emits short the battery passes the self-test.
beeps for one minute. The UPS repeats If the battery fails again, it must be replaced. The connected equipment is
the alarm every five hours. unaffected.

The input circuit breaker trips

The connected equipment exceeds the Unplug all nonessential equipment from the UPS.
specified “maximum load” as defined Reset the circuit breaker.
in Specifications on the APC Web site,
eunic-brussels.eu

The AVR Boost or AVR Trim LEDs are illuminated

The system is experiencing very high or Have qualified service personnel check your facility for electrical problems.
low utility voltage. If the problem persists, contact the utility company for further assistance.

Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual 17

Problem and/or Possible Cause Solution

There is no utility power

There is no utility power and the UPS is Use the cold start feature to supply power to the connected equipment front
off. the UPS battery(s).

Press and hold the button. There will be a short beep followed by a
longer beep. Release the button during the second beep.

UPS operates on battery although line voltage exists

The UPS input circuit breaker trips. Unplug all nonessential equipment from the UPS.
Reset the circuit breaker.

Your system is experiencing very high, Move the UPS to a different outlet on a different circuit: Inexpensive fuel
low or distorted line voltage. powered generators may distort the voltage. Test the input voltage with the
utility voltage display, (see Operation in this manual). If acceptable to the
connected equipment, reduce the UPS sensitivity.

Battery Charge and Load LEDs flash simultaneously

The UPS has shut down. Check that the room temperature is within the specified limits for operation.
The internal temperature of the UPS has Check that the UPS is properly installed, allowing for adequate ventilation.
exceeded the allowable threshold for Allow the UPS to cool down. Restart the UPS. If the problem persists,
safe operation. contact APC at eunic-brussels.eu

Diagnostic utility voltage

All five LEDs are illuminated. The line voltage is extremely high and should be checked by an electrician.

There is no LED illumination. The line voltage is extremely low and should be checked by an electrician.

On Line LED

There is no LED illumination. The UPS is running on battery, or it must be turned on.

The LED is blinking. The UPS is running an internal self-test.

18 Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual

Maintenance, Transport, and Service

Be sure to deliver the spent battery(s) to a recycling facility or ship it to APC in the
replacement battery packing material.

Open battery doors

4x

Remove spent batteries from the UPS

Install new batteries

Smart-UPS VA / Vac Tower/Rack-Mount 5U User Manual 19

The APC Smart-UPS VA is an uninterruptible power supply (UPS) that offers a power capacity of 5 kVA or W. It features an Emergency Power Off (EPO) function, allowing for quick and easy shutdown in case of emergency situations. The nominal input voltage is V, while the nominal output voltage is also V. Equipped with hot-swap battery technology, the UPS allows for easy and convenient battery replacement without interrupting the power supply. The battery type used is Sealed Lead Acid (VRLA), a reliable and commonly used battery technology. The UPS operates at a frequency of 50/60 Hz, ensuring compatibility with a wide range of electrical systems. It provides a typical backup time of minutes at half load and minutes at full load, allowing for sufficient power backup during power outages or fluctuations. With a cable length of meters, this UPS offers flexibility in positioning and installation. Its compact design and premium construction materials ensure durability and reliability over time. Overall, the APC Smart-UPS VA provides a high power capacity and reliable backup system. It is designed to protect critical equipment and systems from power fluctuations, enabling uninterrupted operation.

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the APC Smart-UPS VA below.

Is your question not listed? Ask your question here